8'' Master Precision Level in Fitted Box, Accuracy: 0.0002''/10'', S908-C685

Description: 8'' Master Precision Level in Fitted Box, Accuracy: 0.0002''/10'', S908-C685 Base with V-groove; With cross test vial; With insulating grip; Robust cast iron modelWith full manual instruction in the description partWith insulating gripWith cross test vial Product Description Accusize Industrial Tools S908-C684 S908-C685 S908-C687 6", 8" and 12" Master Precision Level in Fitted Box, Accuracy 0.0002''/10'' Application and Features Application The level is used for checking the straightness or parallelism of the surface of machine tools and other equipment, and the correctness of horizontal and vertical installing positions. You can also use it to measure an object’s inclination. It is packed in a fitted case. There are three sizes: S908-C684 Accusize Industrial Tools 6" Master Precision Level in Fitted Box, Accuracy 0.0002''/10''S908-C685 Accusize Industrial Tools 8" Master Precision Level in Fitted Box, Accuracy 0.0002''/10''S908-C687 Accusize Industrial Tools 12" Master Precision Level in Fitted Box, Accuracy 0.0002''/10" Features: Cast iron body with a ground finished base for high accuracy.Plastic knobs on the frame to insulate the instrument from the heat of the hand.Adjustable main vial with an accuracy of 0.0002''/10" and high transparency.V-grooved base; With cross test vial and insulating grip.DIN 887(& ANSI standard) Setting & Adjustment Setting: To measure the flatness of a machine or a surface, put the level on a reasonably stable and flat surface. It does not have to be perfectly horizontal as far as it does not move. A square granite surface plate is good but any other flat surface like a machine bed or welding table is also acceptable. Before the operation, make sure the work surface is sturdy and clean. Remove all dirt and dust. Remember to ensure the level gets back to the same position after each rotation. Adjustment: Place the level on a reasonably wiped stable and flat surface. If the surface is horizontal, the bubble should be flowing in the middle between two long reference lines. If the surface is not horizontal, the bubble could be at one end, such as flowing at the right like Fig.1. We can use a wrench to adjust the screw under the red cap. For example, when the bubble is at the right like Fig.1, mark down the measurement of the bubble’s position.Rotate the level by 180° end-to-end. If the bubble is still at the same position like Fig.2 or at a similar position and the division is less than 1/2, mark the position down. It is roughly the same as the bubble in Fig.1.Rotate it by 180°. Slightly rotate the adjusting screw with a wrench by a small degree until the bubble reaches the middle between two long reference lines. If the level is like Fig.3 and the difference between the two measurements is the same or at a position that the division is less than 1/2, the level is horizontal and ready to use.If the level still seems incorrect, repeat step (1). Adjusting the level A Adjust the level by turning the adjustment screw under the red cap using a wrench. B Put the level on a reasonably flat surface such as a square granite surface plate. Any other flat surface like a machine bed or a welding table are also acceptable as far as they do not move. Mark down the reading of bubble’s location between these deviations. * The surface is not included. C Rotate the level by 180° end-to-end. And mark down the reading of bubble’s location between these deviations. D You can adjust the center vial by turning the screw with a wrench. Slightly turn the screw and the bubble will move gradually. Watch the screw’s turning direction and the bubble movement carefully. Calibrating E. To determine whether calibration is correct, see if the bubble flows in the same position in both two measurements with the same number of deviations after the level is rotated by 180° every time, and the average measurements of these two are true horizontal levels. And if the bubble flows between the same number of deviations when the level is rotated by 180° every time, it does not have to be at the center. If the bubble flows in different positions in two measurements, the level is not calibrated successfully. Repeat the above steps until the level is calibrated. Measuring increment Mark down the datum of the two measurements, create graphs and see if these two curves are symmetrical.Then calculate the increment.To measure the increment, slide the level along the surface.Mark down the deviations. Warning Keep CleanMake sure the level, surface plate and work area are clean. Remove dust and dirt.Always AvoidAvoid shocks by handling with care. Keep it at a constant room temperature and insulate it with heat and airflow.WaitWait for a stationary bubble before reading the level.Vertical observationRead the bubble with a vertical observation to avoid producing parallax.Always Anti-rustProcess anti-rust procedures after measuring. Pay attention to shockproof and humidity when placing it. Add to Cart Add to Cart Add to Cart Add to Cart Add to Cart Add to Cart Customer Reviews 4.4 out of 5 stars 298 4.2 out of 5 stars 71 4.4 out of 5 stars 298 4.2 out of 5 stars 71 4.4 out of 5 stars 298 4.2 out of 5 stars 71 Price $92.80$92.80 $110.40$110.40 $116.00$116.00 $126.16$126.16 $129.00$129.00 $159.20$159.20 Item # S908-C684 S908-C606 S908-C685 S908-C608 S908-C687 S908-C612 Size 6" 6" 8" 8" 12" 12" Accuracy 0.0002"/10" 0.0002"/10" 0.0002"/10" 0.0002"/10" 0.0002"/10" 0.0002"/10" Premium ✓ ✓ ✓ Packaging In fitted box In fitted box In fitted box In fitted box In fitted box In fitted box Item model number S908-C685 Part Number S908-C685 Style Standard Item Package Quantity 1 Product Dimensions 3.54"L x 2.36"W Material Cast Iron Batteries Required? No Item Weight 4.12 pounds Operation Mode Manual Batteries Included? No Is Discontinued By Manufacturer No Size 8 inch Shipping Fast shipping is very important for us. Our standard US shipping service is FREE. Your order will be shipped within 2-3 business days upon full payment received. Your order will be delivered within 2-3 business days after the handling time. We only ship to the confirmed PayPal address. We reserve the right to cancel any order for any reason at any time. We are not responsible for undeliverable addresses. Returns and payment We offer a 30 days return policy from checkout winning date. We allow only PayPal as payment methodFeedBack Your feedback very important to us, after you get your package and you are satisfied with our service please leave us positive feedback If you have any problem with your order / any questions please before leave any type of feedback For any questions, using eBay contact system Please visit our eBay store to check out other items for sale!Thank you for shopping at our store.

Price: 152.99 USD

Location: Denver, Colorado

End Time: 2024-08-30T08:42:43.000Z

Shipping Cost: 0 USD