Description: 无标题文档 Descriptions: Cv -gun 1 Second Cure White /purple Curing Light Dental Cordless Curing Light 1 Second Cure Lamp 2400mW/cm2 Introduction: 1.Technical specifications： 1.1 Dimensions: 250mm×250mm×240mm 1.2 Net weight: 278g 1.3 Power source 1.3.1 Power supply: rechargeable Lithium battery 1.3.2 Battery mode: ICR 18490 1.3.3 Battery voltage and capacity: 3.7V/ 1400mAh,Battery has protection against Over-voltage, over-current and short circuit. 1.3.4 Adapter Power Input: 100V to 240V, 50Hz/60 Hz Input Power: 10VA Power Output: DC5V/1A 1.4 Light source: 1.4.1 5W high power blue light LED 1.4.2 Checking method: the LED light is fine when the light is on during operating correctly. 1.4.3 The wave length of this product can match with the clinical dental resin solidification 1.4.4 Wave length: 440nm-480nm 1.5 Light intensity:1000-2400mW/cm2 P1 Strong mode:1800-2400mW/cm2 P2 Standard mode:1000mW/cm2~1600mW/cm2 P3 Pulse mode:1200mW/cm2~1600mW/cm2 2. Operation： 2.1 Press the mode button. Following two modes are available. 2.1.1 Strong Mode: screen shows P1, Press the time button to select of time which could be 1 and 3 seconds.Its output light intensity is about 1800-2400mW/cm2 2.1.2 Standard Mode: screen shows P2, Press the time button to select of time which could be 5,10 ,15and 20 seconds.Its output light intensity is about 1000-1600 mW/cm2 2.1.3 Pulse Mode: screen shows P3, press the time button to select of time cold be 5s, 10s, 15s, 20s. It’s output light intensity is about 1000-1600 mW/cm2 2.2 During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, press the ON/OFF button and the main unit will produce "Bi" sound, the curing light radiates blue light and starts working according to the set modes. Meanwhile, it starts counting down and will produce tone at every 5 seconds, it stops working when counting down to "0". 2.3 During operation, the blue light can be stopped by press the power button at any time. 2.4 After a working cycle, operator can press the ON/OFF switch to start another working cycle. Stop operating if the equipment began to heat obviously, do not restart until the equipment cool down. Suggest continues working cycle less than 10 times. 2.5 Low power detective circuit is fixed inside of the main unit, when low power is detected, the display screen of main unit will wink, please charge in time. 2.6 When the battery needs to be charged, connect the plug of the adapter into the AC100V~240V power supply. Then connect the output plug of the adapter to the DC 5.0V input plug of the pedestal, and then the logo turn to blue. Put the main unit to the charging point of the pedestal, the display screen turn to scrolling display, and the curing lights starts charging. 2.7 After operating, take off the disposable sleeve and throw away, forbidden to reuse. 2.8 This equipment will turn off automatically if don't any action within 2 minutes, turn it on by press any button. 2.9 The depth of solidification of composite is no less than 2mm per 1 second. Material: The handle is made of plastic，The lamp holder is made of metal ///////////////////////////////////////////////////////////////// AZ688-2 Wireless Curing Light Wireless LED Curing Light 2000mw/cm² Lamp Test Meter Optical Fiber Because of the Built-in battery of this product and the strict customs, Please be more familiar with local customs and the circumstances before buying. Thanks for your understanding!!! The new brand high quality of curing light has main advantages of others as follows: 1. Excellent quality with competitive price 2. Quick delivery and best service 3. Service tools for dental and easy to maintain and recharge conveniently 4. Large capacity Li-battery can be used for a long one with full charging. 5. Plenty of fiber rods with very reasonable price on sale for you replacement 6. Composes of high power LED, qualified fiber rod. 7. Noiseless; No libration; Generate little heat when working. 8. Imported high power LED and four chips inside. 1. Blue-ray output wavelength:430-485nm. 2. Gradually bright, shiny,bright-wide, the work of three models to choose. 3. Three gear output timing:5s 10s 15s 20s 25s 30s 35s 40s 4. Blue-ray illumination: 5W≥18 5.The effect of curing time: 6s: 2-3mm. 6. Reliable structure and easy operation. Technical Specifications: Wavelength: 380-515nm2 Power density: 99-999mw/cm Only for light probe with a circular emission window: 08-12mm Measuring accuracy: +/-20%Adjustable light intensity: 2000mw/cm2 Operating conditions: Temperature :+10℃to +40℃ Relative humidity: 30% to 75% Ambient pressure: 700hpa to 1060hpa Technical parameters: Output power-----------5w Size ----------------------diameter 270*208*118mm Weight-------------------720g Working voltage--------100-240V AC, 50-60HZ Packing List: Main engine of light-curing Device------1 set Optical Fiber--------------------------------1 piece Battery----------------------------------------1 piece Battery Charge Seat-------------------------1 set Shade Board ---------------------------------1 piece Instruction Booklet -------------------------1 piece //////////////////////////////////////////////////////////////////////////////////////////// YS-C Curing Light Dental Wireless LED Curing Light High Power 2700mw/c㎡ No vibration YS-C Features NAME：LED curing light MODEl：YS-C This high power 2700mw/c㎡ LED Curing Light has a humanity intelligent chip with a high intensity LED light and Li-on rechargeable battery. This device can cure all the dental resin known in the market nowadays; with a performance level far superior than the halogen curing light's, it has 3 different working modes and it can solidify 4-5mm deepness in a few seconds. Benefits： 1)Very convenient to operate. 2)Small size,cordless and light weighted. 3)No dazzling strong light which allows you to aim the light to the exact position and improve the effectiveness of the treatment. 4)No vibration. 5)Noiseless operation. 6)High power rechargeable battery. 7)High powerful light intensity with a maximum reach of 2700MW/cm2. 8)3 different working time modes,exposure time for optional curing:8s/6s/4s. 9) You can select the correct mode according to the different types of material you wish to cure,their speed of reaction,and the clinical protocol you are following. Best Quality Materials: * Mono-fibered glass light guides for various applications. * Anodized aluminum handpiece. * Latest generation of CMS electronics. * Very high-quality single L.E.D. * Li-lon battery with no memory effect Design and Ergonomics: * Silent and hygienic, no fan. * Round surfaces allow for easy and comfortable manipulation. * Compact, lightweight and well-balanced light guide rotates through 360°. * Base-charger can be turned in all directions and low battery warning. * Can be used anywhere in the world. The voltage input is 110V-240V and we will provide you with the correct adapter according to the shipping destination. Specifications: - Blue Light Intensity: 2700mw/c㎡ - Rechargeable Li-ion battery - Spectrum Range: 420nm- 480nm - Power Adapter: AC110-230V / 50-60Hz - Time option:8s/6s/4s - Weight: 0.65kg -Full Metal shell Package Includes: 1 LED Curing Light Device 1 High Capacity Rechargeable Battery 1 Charger 1 Charger Socket /////////////////////////////////////////////////////////////////// X2 Black Curing Lighta X2 White Curing Light Dental Curing Light Broad Band LED High Power AC 100-240V 50 / 60Hz AZDENT Technical Parameters: Light Source:Broad Band LED; Wavelength Range:385 - 515 nm; Light Intensity:> 2300mW / cm²; Battery:Lithium-ion battery (total running time when the battery is fully charged: at least 80 minutes); Power Adapter Input Power:AC 100-240V 50 / 60Hz; Charging time: about 45 minutes; Size:Handle:Φ20 mm × 240 mm; Charging stand: Φ63 mm × 30 mm (all of the above are the largest size) Weight: Handle: 96 grams; Charging seat: 99 grams; Operating ambient temperature: + 10℃ - + 40℃(+ 50 °F - + 70°F); Operating relative humidity: 30% - 75%; Operating environment pressure:700hPa - 1060hPa; Package Contents: 1 × host handle; 1 × charging base; 1 × power adapter; 1 × user manual. Operation and function description: The entire handle is only one button, light built-in button. 1. For the first time, charge the light curing handle first. Plug the USB cable of the charger into the USB port of the power adapter, plug the power adapter into the power socket, and finally Put the handle on the charging stand; or, insert the USB cable plug of the charging stand into the USB port of the computer, and then put the handle on the charging stand. Charging instructions are as follows: | Emerald Flashing | Battery charging; | Emerald green light | battery fully charged; handle removed the charging seat, the restoration of the previous working mode. 2. Working mode selection, by pressing the button for 2 seconds to release to switch the working mode. | Blinking Blue | Progressive mode, working time 10 seconds, light intensity 0-5 seconds from 0-1200mW / cm², 5-10 seconds 1200mW / cm². | Solid blue | Fast mode, working time 3 seconds, light intensity 2300mW / cm ² 3. Turn the light curing lamp on and off, press the button briefly. 4. Switch machine, in standby mode, press the button a short time to open the instrument; stop any operation for 60 seconds, into the ultra-low power standby. ////////////////////////////////////////////////////////////////////////////////////////////// WOODPECKER F*LED-B Curing Light Woodpecker Style Dental Curing Light LED.B Feature: Model:LED.B Wireless Long standby time Working more efficiently Function Keys: ON/OFF button： 1.Turn on or turn off the LED blue-ray output 2.Can make the machine run Time setting: 5s, 10s, 15s, 20s,25s,30s,35s,40s Technical: Changer input: AC 110V—240V50—60Hz The changer output: DC5V 1A Lithium battery voltage: DC4.2V Lithium battery capacity:2200mAh Output optical wavelength:420-480nm Output light intensity:1200—1500mw/cm2 Package: 1 X Curing light 1 X High capacitance rechargeable battery 1 X Charger 1 X Charger socket General Introduction: This curing light has the advantages of adjustable working time, visible working time and high curing efficiency. When the curing light is charging, the charger socket can display the charging status. (Charging: the indicator light is on, Charging over: the indicator light is off. The curing light is removed from the charging socket: Indicator Light begins to flash). When this machine is working, every 5 seconds the buzzer will make a sound of “di” to remind you, at the same time, the screen displays the remaining work time. Nonworking time, this machine can automatic shutdown without any operation in 120 seconds to save electric power. With this machine off, press any key to turn on the curing light //////////////////////////////////////////////////////////////////////////////////////////////////////////// PRO105 Black/White/Purple Curing Light Dental Wireless Cordless Curing Light 1 Second Cure Lamp 1600 mw/cm2 US STOCK Descriptions: mode Dental Wireless Cordless LED PRO105 Curing Light SPECIFICATION: Power supply:Input: AC 100-240V, 50/60Hz Output :DC 5V/1A Intensity High: 1600 mw/cm2 Battery: 3.6V, 2600 mAh (9.36Wh) Handpiece dimension: Φ3.0 cm x 24 cm . Packing List: Main unit of the LED x1 Protective light shield x1 Transformer (100 -240V) x1 USB Type-C Chrging line x1 Instruction manual x1 ///////////////////////////////////////////////////////////////////////////////// Cv -gun 1 Second Cure Purple Curing Light Woodpecker DTE Style LED Dental Cordless iLed Curing Light 1 Second Cure 2300mW Descriptions: Introduction: 1.Technical specifications： 1.1Dimensions: 25mm×25mm×240mm 1.2 Net weight: 280g 1.3 Power source 1.3.1 Power supply: rechargeable Lithium battery 1.3.2 Battery mode: ICR 18490 1.3.3 Battery voltage and capacity: 3.7V/ 1400mAh,Battery has protection against Over-voltage, over-current and short circuit. 1.3.4 Adapter Power Input: 100V to 240V, 50Hz/60 Hz Input Power: 10VA Power Output: DC5V/1A 1.4 Light source: 1.4.1 5W high power blue light LED 1.4.2 Checking method: the LED light is fine when the light is on during operating correctly. 1.4.3 The wave length of this product can match with the clinical dental resin solidification, such as 3M, etc. 1.4.4 Wave length: 385nm-515nm 1.5 Light intensity: 1000 mW/c㎡~2300mW/c㎡ 2. Operation： 2.1 Press the mode button. Following two modes are available. 2.1.1 TURBO Mode: screen shows P1, Press the time button to select of time which could be 1 and 3 seconds.Its output light intensity is about 1800 mW/c㎡-2300mW/cm2 2.1.2 NORMAL Mode: screen shows P2, Press the time button to select of time which could be 5,10 ,15and 20 seconds.Its output light intensity is about 1000 mW/c㎡-1200 mW/c㎡ 2.2 During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, press the ON/OFF button and the main unit will produce "Bi" sound, the curing light radiates blue light and starts working according to the set modes. Meanwhile, it starts counting down and will produce tone at every 5 seconds, it stops working when counting down to "0". 2.3 During operation, the blue light can be stopped by press the power button at any time. 2.4 After a working cycle, operator can press the ON/OFF switch to start another working cycle. Stop operating if the equipment began to heat obviously, do not restart until the equipment cool down. Suggest continues working cycle less than 10 times. 2.5 Low power detective circuit is fixed inside of the main unit, when low power is detected, the display screen of main unit will wink, please charge in time. 2.6 When the battery needs to be charged, connect the plug of the adapter into the AC100V~240V power supply. Then connect the output plug of the adapter to the DC 5.0V input plug of the pedestal, and then the logo turn to blue. Put the main unit to the charging point of the pedestal, the display screen turn to scrolling display, and the curing lights starts charging. 2.7 After operating, take off the disposable sleeve and throw away, forbidden to reuse. 2.8 This equipment will turn off automatically if don't any action within 2 minutes, turn it on by press any button. 2.9 The depth of solidification of composite is no less than 2mm per 1 second. ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////// L800A Sliver 1200mw/c㎡ 1. LED Screen，high quality plastic handle. 2. Noiseless and no vibration when working 3. Lithium battery with large capacity 4. Three Modes: Gradually mode/Flashing mode/All light mode 5. Automatically power down: It will be turned automatically off automatically without pressing button for 3 minutes. 6. Solidification time: 40s Every ten seconds, sound signal to remind operator. The length of work time can be controlled freely. 7. lt has self-protection against exceeding heat after continuous long time work that power– off by itself. After the temperature is normal, operator can use it again. 8. The LED is longevity. Cold light source, no fan. Avoid the infection, cause of air movement.Features:Packing Size: 210*148*71 mm(unit) Packing weight: 420g Wavelength: 440-480nm Light Intensity: 5W≥1200mw/c㎡ Input Voltage: 100-240V 50-60HZ Battery Capacity: DC3.7v 2200mAh Solidification Effect: 5s/3mm You will receive the Purple item !Color available: Green/ silver/ blue/ black/ purple/ Orange/ Golden Please email us or leave us message if you need different color in 2 working days, /////////////////////////////////////////////////////////////////// 1 Second Cure DeepCure 1、The Features of Products •Stable output power guarantees constant light so that the solidification effect is not affected by the consumption of remaining power •Parallel light ensures more focused output energy and better solidification effect. •Wireless charging corresponding to the standards of wireless charging protocol is available •Super capacity battery. A full charge can be used for more than 500 times continuously under 10s working of P2 mode, from full charge to low-battery alert. •Aluminum alloy body, resistance to shatter and drop •Light source featuring 360-degre rotation to realize curing from all directions •Replaceable light source, 400nm-420nm light source with corresponding reagent enables detection of dental caries •A dedicated whitening roller, shooting teeth whitening gel with blue light to whiten teeth •Charger verifying radiation output of LED curing light effective or not •Solidified lens fixed on light source, bonded with all-ceramic veneer and adhered to crown and fiber-reinforced composite root canal post to make solidification effect better. •Replaceable Lithium battery, Auto power-off. 2、Technical Specifications 2.1 Dimensions: 33mm x 27mm x 206mm . 2.2 Net weight: 160g 2.3 Power supply:Different power supply ；Power supply is Rechargeable battery；Rechargeable Lithium battery；Standard voltage 3.7V, capacity:2200mAh；battery model ICR 18650. with protection for overvoltage, overcurrent and short-circuits Power Adapter：Input: 100-240V 50/60Hz；Fuse:T1A 250V；Input power:5VA；Output:5V 1A 2.4 Features of LED light watt high power blue LED light，Class: class 1 Wave length: 400nm²-480nm² Checking: LED light works under proper use Radiation: 850mW/cm² Optical effective area: 75mm LED Curing Light is applicable to some commonly-used resin based materials in dental clinic,such as 3M, ,dentex etc. 2.5 Equipment Safety Classification Operation mode: Intermittent operation mode Protection type against electric shock:class ll, power supply inside the set Protection degree against electric shock: type B Protection degree against inlet liquid: conventional equipment(IPXO) Safety in the case of flammable anesthetic mixture with air, oxygen or nitrous oxide(not AP equipment or APG equipment) 3、Operating Instructions 3.1 Press button "△"for 1 second and release the button when the buzzer warns for once. Following three modes are available •Full Power Mode: The screen shows “∏” The output light intensity is full-power. (recommended mode for clinical) •Progressive Mode: The screen shows “ɲ” The output light intensity enhances gradually power output is to maximum after 5 seconds •Pulsed Mode: The screen shows“∏∏”the blue light works in pulse manner 3.2 Press button "△"for 2 second and release the button when the buzzer warns for twice. Following three modes based on output of power density are available. •Ultra High Power Density: The screen shows "P1" The power density is about 3200mW/cm. •High Power Density: The screen shows "P2", The power density is about 2400mW/cm² •Standard Power Density: The screen shows "P3", The power density is about 1600mW/cm². 3.3 Tap button "△" to select working time interval. In"P3"mode, the time interval can be chose from 1,2,3.4,5.10,15,20 25,30, 35, 40 second In"P2"mode, the time interval can be chose from 1,2,3.4,5, 10,15,20 second In"P1"mode, the time interval can be chosefrom 1,2.3, second Information on the screen is shown in the figure 3.4 During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, press the ON/OF F button ("O" )and the main unit will produce 'Di' sound, the curing light radiates blue light and starts working according to the set modes Meanwhile, it starts counting down from the set working time interval, it stops working when counting down to ("O" )The screen displays the set working time interval again 3.5 Operation can be stopped by paras the ON/OFF button ("O") 3.6 After a working cycle, operator can press the ON/OFF button ("O"). to start another working cycle. Stop operating if the equipment is burning obviously, let equipment cool down before restarting. Suggest continous working cycle less than 5 times. 3.7 Battery Indicator: Low power detective circuit is fixed inside of the main unit.If battery indicator in the screen has only 1 bar left, please charge in time. 3.8 When the battery needs to be charged. plug USB Type A jack in USB Type A plug of power adapter, and connect the plug of power adapter into the AC 100V-240V power supply, and connect Micro USB of USB cable into charge indicator in charge. The blue indicator light on charger indicates charger on standby. Put the main unit to the charging point of the charger, and the indicator light turns green, main unit is detected. Meanwhile,the indicator light at the bottom of main unit turn green, the curing light starts charging. When charging finished, the indicator light at the bottom of main unit turn blue. 3.9 After operating, take off the disposable sleeve and throw away, avoid reusing. Power output will be, decreased by 5-10% if using the disposable sleeve 3.10 The product will turn off automatically if there is And operations within 2 minutes. Turn it on by pressing any button 3.11 The depth of solidification or dental resin composite is not less than 4mm per 10 second. The recommended separation distance between Iuminous point and solidifying point is 2mm ///////////////////////////////////////////////////// 1S CV-215GUN Curing Light Parameter： Wavelength：440-480nm Light power：5W Intensity：800-1400mw/cm² Battery：Li-on 800mAh Input voltage：AC100-240V, 50/60Hz 0.4A Max Output voltage：DC 5V/1.5A Net Weight：155g Mode selection：P1, P2, P3 Solidification time：1S,3S,5S,10S,15S,20S Features: ·Produce the maximum light intensity safely. · A high intensity of 1400 mW/cm2. · Offers extremely short curing times of no more than 3 seconds. · Cordless, highly portable and light weight (only 155g). · High-performance Li-ion battery technology. · LED panel conveniently indicates a countdown curing time. · Battery can be fully recharged in 90 minutes. · Battery with protection against over-voltage, over-current and short circuit. · 3 versatile curing modes for every indications. · Automatic power off, low battery alert. · Color : White . Operation conditions: 1. Storage Condition: Temperature: +10℃+40℃ 2. Humidity: 30%-75% 3. Atmospheric pressure: 70KPa-106Kpa 4. Environment Conditions: Not near from fire equipment or flammability material. Packing list: The host * 1 Metal lamp holder *1 The silicone base *1 Power adapter *1 Disposable protective sleeve *1 Shade plate *1 Product specification *1 //////////////////////////////////// V400 LED 1400 mW/cm2 VRN Dental Wireless LED Curing Light 1400 mW/cm2 2200mAh battery capacity 3S curing Product Parameter:-VOLUME: 33 mm x 29 mm x 246 mm -Net weight: 132 g -Power supply: Chargeable battery: 3.7 V, capacity:2200 mAh, with Protection for over voltage, over current and short-circuits. -Power adaptor: AC100~240 V 50/60 Hz Input power: 10 VA Out power: DC 4.2 V/0.5 A -LED light feature: 5W blue LED light -Wave length: 400 nm~515 nm -Accessible emission limit (AEL): 3.9x10 J -Checking: LED light is working when correctly -Operate Radiation: 1000mW/cm2 ~1400mW/cm2 -Optical effective area of optical fiber:50 mm2 Operation:1 . Choose one of three operation modes by pressing the mode switch button on the curing light. Full power: The screen shows 01, the blue light radiates in full power, light intensity: 1000mW/cm2 ~1400mW/cm2.(recommending mode for clinical) Progressive: The screen shows 02, the blue light power increase stronger continually, after 5 seconds reaches to the highest power，light intensity: 1000mW/cm2 ~1400mW/cm2. Pulse: The screen shows 03, the blue light works on the pulse condition. light intensity: 1000mW/cm2 ~1400mW/cm2. Press the "T"time set button to choose from3, 5,10, 15, 20, 25, 30, 35, 40 seconds for working time. When the shooting period is done, press the "I" on/off button again for next shooting period. If the device becomes hot, the user should stop using the device and wait till the device cooling down. Recommending shooting period is not over 10 times. Low battery alert: This device contains the low battery checking function. When the battery is low of power, the screen will blink. The device will be automatically power off after 1 minutes in idle, and press any button to start. The solidification effect for composite resin is not less than 4mm in 10 seconds. Packing list: Main unit 1pcs Manual 1pcs QC certification 1pcs Power adapter 1pcs Optical fiber tip 1pcs Battery 1pcs Light hood 1pcs ////////////////////////////////////////////////////////////////////////////////////// CV-215-I 10 Sec Cure NEW Dental Cordless Classic LED Dental Curing Light， 2200mAh，metal fuselage Product Description Specification： Size：dia 22*175mm(unit) Weight：165g Safety kind：Ordinary type B,non-continues service,lp40,Class Input voltage：100-240V,50-60Hz Battery capacity： 2200mAh Wavelength：400-515nm Intensity：5W，800-1400mW/cm2 Solidification effect：10 seconds to cure 3mm resin · Operation： A) Power on/off. When the unit is off or stand by,press “power” button to make the unit power on. If press “power” button continues for 2 seconds,the unit should be power off. When the unit is power on,after select work mode press “power” button to make the unit working,the unit should be output blue light,press the button again,working stop and turn to be standby. B) Mode select: press “mode” button to select three types of work modes. “01” Mode: gradually strong mode, light intensity：800-1200mW/cm2, time setting: 10S, 20S, 30S, 40S; “02” Mode: flashing mode，light intensity：800-1200mW/cm2, time setting: 10S, 20S, 30S, 40S; “03” Mode: strong mode, light intensity：800-1400mW/cm2, time setting: 10S, 20S, 30S. C) Time select: press “time” button to select the time type. Four types of time:10/20/30/40 seconds can be chosen. D) When the unit is working,the buzzer will beep every 5 seconds. E) Automatically power down:when the unit is standby and without press button for 8 minutes,this unit will be turned off automatically. F) Low battery alert:every time open the unit power,if the voltage of the battery is lower than the set point,this unit will be alarm.The buzzer beeps 5 times and the indicator flashes in the stage,please charge the battery in time. Operation conditions: Storage Condition: Temperature: +10℃+40℃ Humidity: 30%-75% Atmospheric pressure: 70KPa-106Kpa Environment Conditions: Not near from fire equipment or flammability material. Packing list: 1. Main unit-------------------1 set 2. Light guide rod------------1 piece 3. Battery----------------------1 piece 4. Charging Holder-----------1 piece 5. Charger ---------------------1 piece 6. Light shade plate-----------1 piece 7. User’s manual--------------1 pieces ///////////////////////////////// ////////// ////////// ////////// 1 Second Cure 2200mW/cm² Light source: 10W high power blue light LED. Checking method：the LED light is fine when the light is on during operating correctly. The wave length of this product can match with the clinical dental resin solidification, such as 3M,etc. Wave length：385nm-515nm. Light intensity：800mW/cm²-2200mW/cm². Operation Press the mode button.Following three modes are available. Strong Model：screen shows P3,press the button to select of time which could be ls,3s.its output light intensity is about 1800mW/cm²-2200mW/cm². Standard Mode: screen shows P2,press the time button to select of time which could be 5s,10s,15s,20s.Its output light intensity is about 800mW/cm²-1200mW/cm². Pulse Mode: screen shows Pl, press the time button to select of time which could be 5s,10s,15s,20s.Its output light intensity is about 800mW/cm²-1200mW/cm² Technical specifications： Dimension：25mm×240mm Net weight：278g Power supply：rechargeable Lithium battery Battery mode：ICR 18650 Battery voltage and capacity：3.7V/2200mAh Battery has protection against Over-voltage, over-current and short circuit. Statement The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, you can bid it on this item only if you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item. Seller name:DentalinchinaCity,State:SHENZHEN,ChinaTelephone number:0755-6895621 Payment We accept PayPal Only! All payments must be made within 7 days after the auction ends. Non-paying bidders will be reported to eBay. Please don't buy an item if you can't/won't pay for it. Paypal is the easiest way to pay for items on eBay. Please make sure your Paypal and eBay accounts have the same physical address used for delivery and the same e-mail address to ensure payment confirmation.Shipping: Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Shipping The goods you odered will be posted out in the second working day after the paymet has been made. (We will inform you via email if any delay occured due to holiday events. General shipping time is between 7-12 working days. (After the shipping started, the order will be monitored and the track of the item will be posted on paypal. Return If the item you received is damaged or defective,Please contact us immidately.We will free exchange or refund.We will pay the return shipping costs if the product is defective or the return is a result of our error. If the item is returned for any other reason you are responsible for the return shipping charges.You can return your purchase for up to 15 days from the date of delivery. No refund will be issued if the product shows signs of use. Returned package must be in the original packaging, everything must be in new condition, No missing parts.Our guarantee does not cover accidental damage or wear of product caused by customer.Thank you very much for your understanding! Feedback Your feedback is VERY important to us ^_^ Please leave us positive feedback, an positive feedback will be automatically left for you once we receive your full payment. Please leave us with any concerns prior to leave negative feedback, as we can only correct issues when we are aware of them. We understand the concerns and frustrations you might have, and will try our best to resolve the isuues. Contact Us Serivce is our #1 priority ! If you contact us immediately after placing the order, we will make every effort to assist you with your change request. Unfortunately, we can not make changes or cancel an order once it has shipped. We offer the best items at the best prices. We strive to exceed all your expectations and put a smile on your face. Your experience will be a pleasant and effortless one when you buy . We stand behind our products and pride ourselves on OUTSTANDING customer service. We guarantee that you will be delighted with your purchase or we will gladly and promptly issue you a refund or make things right! Statement:The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. So you can bid it on this item only if you are an authorized purchaser. If the item is subject to FDA regulation,We have to verify your status as an authorized purchaser of this item before shipping of the item. Thanks for your understanding! Payment 1.We accpet the payment via paypal, PayPal is safest, quickest and secure for seller and buyer. 2.All major credit cards are accepted through secure payment processor PayPal. 3.Payment must be received within 7 business days of auction closing. Shipment 1.We accpet the payment via paypal, PayPal is safest, quickest and secure for seller and buyer. 2.Tracking info of your parcel is available. 3.Returns could be accepted within 60 days after receipt of the item. 4.Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer is responsibility. Please check with your country is customs office to determine what these additional costs will be prior to bidding/buying. Destination Delivery Time Working Days 7-12 10-15 15-25 25-40 >50 US Item arrived 80% 10% 8% 1% Refund ASIA Item arrived 30% 40% 20% 10% Refund EU Item arrived 20% 20% 50% 10% Refund AU Item arrived 30% 30% 20% 20% Refund Other Countries Item arrived 5% 10% 10% 60% -- Return & Refund policy We accept returned in some exceptional cases, please send message before return item(s) otherwise returned item(s) will not be accepted. Buyer is responsible for return shipping cost and we will ship the replacement or make the refund within 2 days after returned item is received. If it is our fault, we will be responsible for the return postage. Feedback We will leave feedback upon receipt from cutomer. If you are dissatisfied for any reason, please don't be quick to leave negative/neutral feedback or open a dispute. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers. If you are satisfied with the product you received, please leave us positive feedback and 5 scores DSR. Please call five satisfaction Item as described Communication Shipping time Shipping and handing charges About Us We're one of the largest online dental suppliers based on many qualified manufacturers in china. We supply all dental items with very nice qualities and the best reasonable prices for worldwide dentistry students, dentists, and other professionals. Any interests or questions, please do not hesitate to send message. Looking forward to our friendly & win-win cooperation.
Price: 13.9 USD
Location: Shen Zhen
End Time: 2024-09-26T21:36:49.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Seller
All returns accepted: Returns Accepted
Item must be returned within: 60 Days
Refund will be given as: Money back or replacement (buyer's choice)
Brand: Unbranded
Unit Type: Unit
Light Type: LED
MPN: D
Country/Region of Manufacture: China
Unit Quantity: 1
Intended Use/Discipline: Dental Laboratory, Dentistry, Endodontics
Available Variations
Color: AZ688-2 Wireless Curing Light
Price: 66.87 USD
Available Quantity: 107
Quantity Sold: 37
Color: YS-C Curing Light
Price: 53.67 USD
Available Quantity: 117
Quantity Sold: 47
Color: X2 Black Curing Light
Price: 62.92 USD
Available Quantity: 105
Quantity Sold: 35
Color: X2 White Curing Light
Price: 62.92 USD
Available Quantity: 80
Quantity Sold: 10
Color: WOODPECKER F*LED-B Curing Light
Price: 38.71 USD
Available Quantity: 138
Quantity Sold: 83
Color: PRO105 Black Curing Light
Price: 56.31 USD
Available Quantity: 101
Quantity Sold: 31
Color: PRO105 White Curing Light
Price: 56.31 USD
Available Quantity: 73
Quantity Sold: 14
Color: PRO105 Purple Curing Light
Price: 56.31 USD
Available Quantity: 67
Quantity Sold: 7
Color: Cv -gun 1 Second Cure Purple Curing Light
Price: 65.99 USD
Available Quantity: 78
Quantity Sold: 19
Color: Cv -gun 1 Second Cure White Curing Light
Price: 65.99 USD
Available Quantity: 70
Quantity Sold: 14
Color: L800A Sliver 1200mw/c㎡
Price: 32.55 USD
Available Quantity: 73
Quantity Sold: 15
Color: 1S CV-215GUN Curing Light
Price: 46.63 USD
Available Quantity: 66
Quantity Sold: 6
Color: AZDENT plus105 1 Second Cure Purple
Price: 1033.11 USD
Available Quantity: 2
Quantity Sold: 2
Color: AZDENT plus105 1 Second Cure White
Price: 61.59 USD
Available Quantity: 62
Quantity Sold: 2
Color: AZDENT plus105 1 Second Cure Black
Price: 61.59 USD
Available Quantity: 67
Quantity Sold: 8
Color: V400 LED 1400 mW/cm2
Price: 38.71 USD
Available Quantity: 68
Quantity Sold: 8
Color: CV-215-I 10 Sec Cure
Price: 1011.11 USD
Available Quantity: 5
Quantity Sold: 5
Color: 1S Cure 2500mW/cm2
Price: 45.75 USD
Available Quantity: 3
Quantity Sold: 3
Color: 1 Second Cure 2200mW/cm²
Price: 65.99 USD
Available Quantity: 62
Quantity Sold: 4
Color: 1000pcs Guide Stick Sleeve
Price: 13.9 USD
Available Quantity: 10
Quantity Sold: 0
