GREASEBUCKET Grease Bucket Tone Upgrade Get The Best Pro Performance EZ Install

Description: ‘‘ Do You Want True "Pro" Grease Bucket Sound? ‘‘ Our Professional Upgrade Makes It Easy For You! ’’ Thank you for looking at our incredible upgrades for your electric guitar and bass. Want the Best performance from your instrument? We have innovative alternatives for You. Do You want increased performance, enriched playing enjoyment, and the freedom to be more creative? Our products are the absolute BEST — Nothing on Earth is Better! Customer Comments Very easy to use. I used this one and I hand built my own with similar specs and you can tell the difference. Only difference is, this one is an easy and clean connect and mine took a little longer and not as compact. Excellent service and pleased with purchase. Thank you! Perfect Do You Need The Absolute BEST Grease Bucket Upgrade? The "tone" controls of your electric guitar or bass is an adjustable low-pass filter. It let only the low frequencies pass through to the amplifier while the high frequencies get sent to ground through the tone capacitor. A typical "tone" control circuit (used in a Stratocaster, for example) has a 250K pot with a .022uF capacitor. As the tone is rolled off with a regular tone control, bass frequency becomes more prominent. A Grease Bucket tone circuit also uses a 250K pot with .022uF capacitor. But it has an additional 4.7K resistor and .1uF capacitor. It is a vastly improved tone control that combines a high-pass and a low-pass filter to let just the middle frequencies pass through to the amplifier. Basically, it stop your tone control from producing a noticeably "muddy" signal. This makes your Stratocaster, Telecaster, Jazz Bass (and every other instrument's) tone control(s) more useful. Many professional guitar players now use Grease Bucket to eliminate muddiness in a distorted sound. Normally, a Stratocaster has three 250K pots. One for the Volume control and the other two for what we call "tone". A standard Telecaster has two 250K pots, one for volume and the other for tone. In the "stock" Stratocaster, the tone pots share a common .022uF capacitor. But in the Grease Bucket circuit, each "tone" pot has it's own .022uF capacitor, 4.7K resistor, and a .1uF capacitor. This means that the "tone" pots are no longer tied together. To convert your Stratocaster or Telecaster normal tone controls to Grease Bucket specifications, you simply attach our GB-Pro-1 upgrade to your Tone control. Stratocasters need two upgrade products if you want to do both Tone controls; your Telecaster uses just one upgrade product. You also need to remove the stock capacitor on each Tone control, and take the wire that is connected to the tone control's terminal #3 and connect it to terminal #1. We made this simple for you. You just cut the wire at the terminal #3 and connect it to the RED wire attached to the GB-Pro-1 upgrade. An included UY2 connector lets you connect the two wires using pliers. Because our upgrades mirror Fender specifications, you just "drop it in" and capture its benefits. Works with 250K & 500K pots. Works with all Single Coils & Humbuckers. Completely passive-No battery needed. Does not affect your tone at full clockwise setting. Mounts to any standard or "mini" tone pot. Flip it over and mount it to push-pull pots We use mylar capacitors. Warning: Ceramic caps will give you the worst frequency response. Best grease bucket upgrade. Lowest cost. Buy several and save on shipping. Simple installation. Comes with simple instructions. To install this upgrade, you need a low heat soldering iron, rosin core solder, wire cutters and pliers. You can see the installation instructions HERE: https://www.awesome-guitars.com/_files/ugd/c3cc09_f668e8da43664c6eb6367dccd393dd1e.pdf How To Install Your Grease Bucket Upgrade Clip and remove the stock capacitor (the included instructions show you where and how).Clip the wire connected to tone control terminal #3 and connect it to the RED wire (tone control terminal #1) using the supplied UY2 connector.Remove the backing from the adhesive tape under your Grease Bucket circuit board. Move the slots of the circuit board as close as possible to the three tone control terminals to make physical contact, then press the circuit board down on the back of the tone control. The adhesive tape will hold it in place.Flow solder on all three tone control terminals and your Grease Bucket circuit board slots. Just "tack" the connections and avoid excessive solder. Note: if direct contact between the the circuit board slots and the tone control terminals is not possible, use insulated wires that are soldered to each tone control terminal and to the corresponding circuit board slot.Connect (solder) your Grease Bucket circuit board BLACK wire to common ground. Now you can enjoy superior performance from your electric guitar or bass with this upgrade. Closing Notes Quality U.S.A. Seller Gives You Fast Shipping! Because the "Greasebucket" name is a registered Fender trademark, we use two separate common English language words "Grease Bucket" to describe our GB-Pro-1 upgrade product. This auction gives you the selected quantity you want for our GB-Pro-1 Grease Bucket Upgrade. Note: Only the GB-Pro-1 Grease Bucket Upgrade is being sold. The pots are not included, but are only used to show how the upgrade is mounted to these components to simplify your wiring efforts. Purchasing Details Payment: All eBay accepted payment methods. Shipping: Item is shipped via United States Postal Service. We ship within 1-3 days of payment. Other: No Returns. We are always happy to answer your questions. Other Information Note 1: We are the creator and sole owner of all of these incredible upgrade products. Note 2: Ask questions before purchase. Note 3: We do NOT cancel bids made in error. If you made an error, you are responsible for canceling your bid. Note 4: We only use USPS First Class mail to ship these items. © 2023 AweSome-Guitars, All rights reserved Worldwide

Price: 23 USD

Location: Romulus, Michigan

End Time: 2023-12-19T13:22:39.000Z

Shipping Cost: 0 USD