GroundWorx SF ESD Static Dissipative Epoxy Floor Coating | Water Based

Description: GroundWorx SF ESD Static Dissipative Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-2014 GroundWorx™ Static Dissipative Seamless Poured ESD Epoxy Floor Coating | ANSI/ESD S20.20-2014 GroundWorx SF is a budget friendly, static dissipative 2 component abrasion resistant water based durable system designed for superior anti-static protection of interior concrete floors, wood, VCT tile in electronics manufacturing, assembly and ESD protected areas. Surface resistivity measures 106 - x 109 ohms per square average. Conforms to ANSI/ESD S20.20-2014 when tested according to ANSI/ESD STM7.1 GroundWorx EC combines permanent conductivity, durability and value for applications requiring an inexpensive, easily installed ESD floor coating. GroundWorx ESD Static Dissipative Epoxy meets the static control flooring requirements of ANSI/ESD S20.20-2014 (S97.1 and S97.2). GroundWorx is a two part polymeric ESD epoxy coating that can be applied by both novices and professionals. Many of our clients actually apply their GroundWorx ESD floor themselves. GroundWorx is extremely easy to repair; it's ideal for challenging applications like warehouses and fork lift applications. GroundWorx can even be installed in occupied spaces with adequate ventilation. GroundWorx Static Dissipative Epoxy provides a seamless matte finish to almost any sub-floor surface and comes in a 4 gallon kit. The Static Dissipative version of Groundworx is special order 3-4 week lead time. Most projects use the Conductive Version of GroundWorx with immediate shipment of Pewter color PRIMER: For applying directly to VCT, ceramic tile, vinyl, linoleum or asbestos mastics, cutback and carpet glues with minimal preparation consider our Perfect Primer Sealer . TOPCOAT: Optional: None required. For additional physical protection as a low cost sacrificial option, and decorative gloss use the CoatZF ESD Low-Voc Dissipative Clear Floor Finish Our Static Dissipative Groundworx Epoxy is a special order product and is available in 6 colors with a 40 gallon minimum order and 2-3 week lead time before shipping. Use this link for a static conductive version of the Groundworx ESD Static Conductive Epoxy which is in the conductive range 2.5 x 104 – 3.5 x 107 ohms and offers system resistance (w/ ESD Footware) < 3.5 x 107 (fully compliant) ANSI/ESD STM 97.1. We offer the option to include a 1/2" wide copper grounding strip for grounding to earth grounds. Copper is 1.4 mil thickness (2.6 mil thickness with the conductive adhesive backing). Recommend at least 1 grounding strip every 1,000 sq' of project surface area. See the guide: For cleaning and maintenance of your GroudWorx SF epxoy floor, recommend the StaticWorx TriboClean to clean and renew the anti-static properties. To extend the life of the GroundWorx Expoxy Floor Coating, recommend application of the GroundWorx CoatZF coating. For floor surfaces subject to heavy wheeled traffic use including forklift and pallet jack traffic, we offer our HB-97.2 Coating System which includes a high performance 2 part 100% solids epoxy basecoat and high solids urethane topcoat for excellent ESD anti-static control in a physically demanding environment. For more information on anti-static floor systems, see our video library. Where is GroundWorx Static Dissipative Epoxy typically used? Electronic Assembly Test, Repair and Handling Data and Telephony Closets BGA rework Shipping, Receiving, Warehouses Leased spaces Pallet drop zones Box build SMT Any space requiring permanent low cost ESD flooring. Why GroundWorx ESD Anti-Static Paint? Water - based epoxy, matte finish Static Dissipative 10e6 - 10e9 ohms Great low cost solution for concrete, wood, VCT Tile floors Extended working time - POT life 6 hours Quick turnaround - Light traffic 12 hours after application Simple, easy to apply formula for novices and professionals Easy to maintain See sample ESD Control Program Template for company Meets ANSI/ESD S20.20-2014 (S97.1 and S97.2) Good chemical & abrasion resistance TECHNICAL INFORMATION Color 3 colors to select from Sheen/Gloss Level Matte finish Dry Time 5-7 hours to touch #Coats Recommended 2 coats Material Type Epoxy 2 component Application method Airless sprayer, roller, brush Solids 37% +/-1% Back in-service Time 12 hours for light traffic POT Life Must use all product within 6 hours pH level 6.0 - 7.0 Hardness 30 (Sward) Slip Resistance > 0.5 SCOF New Concrete Cure Wait 30 days before application Warranty Available Yes, see Documents Tab Above Full Chemical Cure 5-7 days Packaging Each 4 gallon kit comes with (4) 1 gallon pails of Part A and (4) 11 oz bottles Part B catalyst to be mixed together Coverage Rate - 2 Coats recommended Square Feet/Gallon Per Coat Coat 1 400 - 500 Coat 2 500 - 600 PACKAGING OF 4 GALLON KIT Shipped in (4) 1 gallon kits Each kit contains 1 gallon container partially filled with Part A (colored resin) and separate small bottle for remainder of gallon filled with Part B (hardener) PREPARATION New concrete floors should be allowed to cure a minimum of thirty days. Application to floors colder than 60 F is not recommended. Floor surfaces must be free of any release agents, curing compounds, salts or efflorescence before coating. Sweep and then wash floors with an appropriate cleaning product to remove oil, grease, and soil. Follow by etching surface with an etching solution, and then thoroughly rinse with clean water. Ideal preparation on concrete is to rough up floor mechanically with grinder for a 100 grit sandpaper like feel or 80 grit sander. Catalyzed GroundWorx™ should be used within six hours of mixing. Therefore, prepare only the quantity necessary for immediate use. Add pre-measured catalyst to epoxy base. Stir gently until the catalyst has been thoroughly mixed in. Allow catalyzed GroundWorx to stand for 5 minutes. MIXING Mix one 1 gallon kit at a time You have 20 minutes working time once mixed. 5 minutes to catalyze (let sit after mixing A and B) and 15 minutes to apply Use drill paint mixer and mix Part A (resin with color) for 2 minutes very slow speed to minimize introduction of air bubbles After mixing let mixed material stand for 5 minutes to catalyze before using. After 5 minutes letting catalyze, immediately being applying Catalyzed GroundWorx should be used within six hours of mixing APPLICATION Apply catalyzed GroundWorx with a short-nap lint free 1/4" or 3/8" roller cover specifically meant for epoxies applied in thin, uniform coats. Divide floor into grids. Each grid should be what you anticipate a gallon kit to cover. Can apply 2 ways. Pour into roller pan and dip and roll OR pour the mixed and catalyzed 1 gallon kit onto floor in a zig zag ribbon onto floor The initial coat coverage rate will vary depending on surface applied to. On bare concrete first coat applied at 250-300 sq'. On smooth non-porous surface such as VCT or tile first coat will cover approximately 400-500 sq'/gallon. Allow the initial coat to dry for 5-7 hours until dry to the touch then apply a second coat. Second coat coverage is approximately 500 sq'/gallon. A 3rd coat is strongly recommended when applying to bare concrete. For all projects a 3rd coat can be applied for increased physical durability of the GroundWorx coating applied at 500 sq'/gallon. Under normal curing conditions, the finished floor may be opened to light traffic after 12 hours and full foot traffic in 24 hours. Heavier traffic in 36 hours and complete curing with maximum durability and chemical resistance will take 5-7 days Electrical Grounding The GroundWorx SF coating must be grounded to an earth ground once every 1,000 square feet for proper static dissipation. The EOS/ESD Association provides instruction for proper grounding of ESD equipment and floors. We offer the option to include with the GroundWorx Epoxy, a 1/2 inch-wide copper grounding strip for grounding to earth grounds. Copper is 1.4 mil thickness (2.6 mil thickness with the conductive adhesive backing. See the following guide on how to properly ground the GroundWorx SF Epoxy for your floor coating system: HOW TO GROUND ESD COATINGS If floor has been previously coated, a small area should be cleaned, roughed up by screen disking with an 80 Grit screen. A single application of GroundWorx - SF should be applied over the old coating and allowed to dry. The trial area should be tested for adhesion, lifting, etc. Any areas of the existing coating which display poor adhesion should be stripped. Wash the stripped areas, acid etch, and rinse thoroughly. Allow the floor to dry. Catalyzed GroundWorx - SF should be used within six hours of mixing, therefore, prepare only the quantity necessary for immediate use. Add premeasured catalyst to epoxy base. Stir gently until the catalyst has been thoroughly mixed in. Allow catalyzed GroundWorx - SF to stand for 5 minutes. Apply catalyzed GroundWorx - SF with a short nap roller in thin, uniform coats. The initial coat will cover approximately 400-500 ft2 per gallon. Allow the initial coat to dry for 5-7 hours, and then apply a second coat. Second coat coverage is approximately 500-600 ft2 per gallon. NOTE: This product is not recommended for applications that experience reoccurring standing water. Finished floors may be opened to light traffic, under normal curing conditions, after 12 hours. Complete curing with maximum durability and chemical resistance will take 5-7 days. SCHEMATIC FOR GROUNDING AN ESD FLOOR COATING Maintenance Using Staticworx maintenance products, GroundWorx epoxy is easy to clean and maintain. Simply apply Staticworx Eco Scrub degreaser, followed by ScrubWorx cleaner, and CoatZF Sealer. NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products Size Color Price Case 4 Gallons with 1 Copper Ground Strip Teal 1,190.25 Case 4 Gallons with 1 Copper Ground Strip Emerald 1,190.25 Case 4 Gallons with 1 Copper Ground Strip Black 1,190.25 Case 4 Gallons with 2 Copper Ground Strips Teal 1,201.75 Case 4 Gallons with 2 Copper Ground Strips Emerald 1,201.75 Case 4 Gallons with 2 Copper Ground Strips Black 1,201.75 Case 4 Gallons Teal 1,178.75 Case 4 Gallons Emerald 1,178.75 Case 4 Gallons Black 1,178.75 Case 4 Gallons with 1 Copper Ground Strip Biege 1,190.25 Case 4 Gallons with 2 Copper Ground Strips Platinum Gray 1,201.75 Case 4 Gallons with 2 Copper Ground Strips Pewter (IN-STOCK) 1,127.00 Case 4 Gallons with 2 Copper Ground Strips Biege 1,201.75 Case 4 Gallons with 1 Copper Ground Strip Platinum Gray 1,190.25 Case 4 Gallons with 1 Copper Ground Strip Pewter (IN-STOCK) 1,115.50 Case 4 Gallons Platinum Gray 1,178.75 Case 4 Gallons Pewter (IN-STOCK) 1,104.00 Case 4 Gallons Biege 1,178.75 Shipping Shipping cost:No cost shipping lower 48 US States FedEx Ground Delivery time:Typically 3-5 days to process order plus 1 to 5 days transit time after shipment depending on location Payment We accept the following payment methods: PayPal payment due at time of order placement Please contact us if you have any questions. Service PLEASE CONTACT CUSTOMER SERVICE FOR QUESTIONS

Price: 1104 USD

Location: Charleroi, Pennsylvania

End Time: 2024-01-31T03:12:20.000Z

Shipping Cost: 0 USD