Keysight DSO1052B Oscilloscope 50MHz Bandwidth 2 Channel

Description: Used oscilloscope in good condition.Includes the following:2 P6100 probes (generic)power cordprinted manual (non bound) and certificate of calibrationNote:one inch blemish on top (see picture). Data sheet---------------Performance characteristics Bandwidth (-3dB): DC to 50 MHzReal-time sample rate: 1 GSa/sec half channel interleaved, 500 MSa/sec all channelsMemory Depth: 16 kpts half channel interleaved, 8 kpts all channelsChannels: 2 channels Vertical resolution: 8 bitsVertical sensitivity (range): 2 mV/div to 10 V/divDC gain accuracy: 2 mV/div to 5 mV/div: ± 4.0% full scale 10 mV/div to 10 V/div: ± 3.0% full scale (B models only)Vertical zoom: Vertical expand Maximum input voltage: CAT I 300 Vrms, 400 Vpk;transient overvoltage 1.6kVpkDynamic range: +6 divisions from center screenTime-base range: 5ns/div to 50 sec/divSelectable BW limit: 20 MHzHorizontal modes: Main (Y-T), XY, delayed zoom and rollInput coupling: DC, AC and groundInput impedance: 1 MΩ ±2% in parallel with 15 pF ± 3 pFTime scale accuracy: ± 50 ppm over 1 msAcquisition modes: Normal: Displays sampled data directly to the screen in real time Averaging: Selectable from 2, 4, 8,16, 32, 64, 128 or 256 Sequence: Selectable 1 to 1,000 acquisition frames can be recorded, played back and stored in the scope memory or external USB memory Peak detect: Captures high-frequency glitches as narrow as and 20 nsec when viewing signals at slow sweep speeds Roll: Waveform display rolls from right to left. minimum horizontal scale setting is 50 msec/div.Interpolation: Sin (x)/xTrigger coupling: AC, DC, LF reject, HF rejectTrigger modes: Force: Triggers immediately when front panel button is pressed Edge: Triggers on the positive and/or negative slope on any channel Video: Triggers on NTSC, PAL or SECAM video signals Pulse width: Triggers on pulse width greater than, equal to or less than a specific time limit, ranging from 20 nsec to 10 sec (A models) and 50ns to 10 sec (B models) Alternate: Triggers on two non-synchronized active channelsTrigger source: Ch 1, 2, Ext, AC Line (edge only)Trigger sensitivity: ≥5 mV/div: 1 div from DC to 10 MHz, 1.5 div from 10 MHz to full bandwidth Cursor measurement: Manual, track waveform or automatic measurement selections. Manual and track waveform selections provide readout of Horizontal (X, ΔX) and Vertical (Y, ΔY)Auto measurement: Voltage: Maximum, minimum, peak-to-peak, top, base, amplitude, average, RMS, overshoot, preshoot Time: Period, frequency, rise time, fall time, + width, - width, +duty cycle, -duty cycle, delay A-->B (rising edge), delay A-->B (falling edge), phase A-->B (rising edge) and phase A-->B (falling edge)Counter: Integrated 6-digit frequency counter on any channel. Counts up to the scope’s bandwidthDisplay all measurements: Mode to display all single-channel automatic measurements simultaneously on the displayMath functions :A+B, A-B, AxB, FFT Source channel selection for A and B can be any combination of oscilloscope channels 1 and 2AutoScale: Finds and displays all active channels, sets edge trigger modes on highest numbered channels, sets vertical sensitivity on channels, time base to display ~2 periods. Requires minimum voltage >20 mVpp, 1% duty cycle and minimum frequency > 50 Hz Display: 5.7 inch diagonal color QVGA TFT LCD display with 300 cd/m2 backlight intensityDisplay persistence: OFF, InfiniteDisplay types: Dots, Vectors Waveform update rate: 200 wfm/sec Save/Recall internal: 10 setups and 10 waveforms can be saved and recalled using internal non-volatile memory locations. 1 reference waveform can be saved and recalled using an internal volatile memory location for visual comparisons. Save/Recall external: Setups: STP saved and recalled Waveforms: WFM saved and recalled, CSV saved Reference waveforms: REF saved and recalled for visual comparisons Images: 8-bit BMP, 24-bit BMP, PNG saved

Price: 150 USD

Location: San Pablo, California

End Time: 2024-10-20T20:06:34.000Z

Shipping Cost: N/A USD