UBERTI SAA GRIPS Cattleman, Evil Roy, El Patron, Pistoleer ~ 2P WHITE SCROLL QR

Description: Arizona Custom GripsUBERTI SAA(SINGLE ACTION ARMY REVOLVERS)~ Exclusive ~ MAGNA-TUSK™white ivoryscroll engraved GRIPS(QR Coded Packaging)Milled out of a solid block of Magna-Tusk, denser and heavier than regular Ivory or Stag. See below for details.~~~~~two-PIECE (with SCREWHOLE) STYLETHIS AUCTION IS FOR OUR TWO-PIECE (SCREWHOLE) STYLE GRIPS. SEE BELOW.********ONE-PIECE VS. TWO-PIECE STYLE GRIPS:Note: Two-Piece style grips incorporate a visible screw and screwhole, allowing easy and quick removal for cleaning or maintenance of your revolver. One-Piece style grips do not use a screw but instead use an internal spacer. We sell both types. Both styles are traditional and historical designs and both were originally used on early Colts, so it is a matter of personal preference. Both styles of our grips will interchange and work on either style of grip frame, no matter how your revolver is currently set up. See below.One-Piece style grips (i.e., grips which do not have a visible screwhole in the grips) incorporate a user installed spacer (which is included with the grips) between the grip panels, as seen on many of the early Colts. The spacer supplied with your grips is sent unmounted to ensure optimum fit with your revolver, with simple, quick installation which takes about one minute or so per panel. Fully illustrated instructions are included. This results in a rock-tight fit, without the need of a screw. Preferred by many collectors for their clean lines and traditional look. One-Piece style grips are removed by removing the three backstrap screws, and pulling the grip and backstrap backwards. Reinstallation is in reverse order. Alternatively, our Two-Piece style grips (i.e., grips with a visible screw and screwhole) offer the superior convenience of quick grip removal. Our grips include a free Conversion Kit, allowing their use on revolvers that are currently set up for One-Piece style grips that do not have a grip pin. The Conversion Kit replaces the need for a grip pin and is actually a stronger design, and allows the grips to lock up tight on the frame, allowing no movement. This requires no modification to your revolver and gives you the advantage of the ease of maintenance of Two-Piece grips, while preserving the integrity of your revolver in original factory condition. Two-Piece style grips were also used on many of the early Colts, and are a traditional and iconic historical design, offering a distinctive look and convenience preferred by many collectors.Fully illustrated, detailed instructions are included with each set of grips. 06302300~~~~~WHAT THESE WILL FIT(Please read this entire section carefully in order to make sure you get the correct grips): These WILL FIT any of the UBERTI Single Action Army style revolvers, with the standard sized SAA “plowhandle” grip frame, which measures around 3-1/16” to 3-1/8” tall, depending on how you hold your ruler, tape, or caliper. [Attention: Please see the note regarding the non-standard, taller sized (3-3/8”) 1860 Army sized gripframes, below]. This includes any of the following (all of which are made by Uberti and imported by Cimarron, E.M.F., Taylor’s & Co., Stoeger, etc.):● Cimarron Uberti revolvers: Buntline; Cattleman; Cattleman II; Chisholm; Desperado; El Patron; Evil Roy; Frisco; Holy Smoker; Hombre; Horseman; Cimarron Model P and Model P Jr.; New Sheriff; Old West; Pistoleer; Rooster Shooter; Short Stroke CMS Pro; Short Stroke SASS Pro; Stallion; Thunderstorm and Thunderstorm CM; US Military Models (Custer 7th Cavalry, U.S. Cavalry Scout, and U.S.V. Artillery); Wyatt Earp Buntline, and Wyatt Earp Cody; ● Taylor’s & Co. Uberti revolvers: Cattleman (NOTE: these will NOT fit the Cattleman .44 Mag which uses the larger 3-3/8” gripframe – see below); Cattleman 12-Shot; Devil Anse; Drifter; Gambler; Old Randall; Outlaw Legacy; Ranch Hand; Runnin’ Iron; Smoke Wagon; Stallion .22, Taylor Gambler; and Taylor Marshall. (Note: these grips will NOT fit the Taylor’s Gunfighter or Gunfighter Defender, both of which use the larger 3-3/8” gripframe – see below);● Also: Will also fit any of Stoeger’s Uberti revolvers; the E.M.F. Dakota II or Dakota III; the American Arms Regulator; ● or any other Uberti SAA style revolver with the standard sized (3-1/6” to 3-1/8”) plowhandle grip frame.Note: If you do not see your revolver listed, please drop us an email with your model name and we will verify your revolver.ATTENTION: Please note that these grips will only fit Uberti revolvers having the standard sized SAA style gripframe (around 3-1/16” to 3-1/8” tall depending on how you hold your ruler, tape, or caliper). These WILL NOT fit Uberti gripframes that are around 3-3/8” tall (such as Taylor & Co.’s Gunfighter or Gunfighter Defender, Taylor’s Cattleman 44 Mag., Cimarron’s Bad Boy, the El Patron Grizzly Paw, the Uberti Callahan, etc). Please check your revolver carefully before ordering. If you have one of these taller frames, our Uberti 1860 Army “Conversion & Metallic Cartridge” grips will fit these revolvers. You can locate these in our store. Please contact us if you cannot find what you need and we will be happy to help you. UBERTI FRAME VARIATIONS -- IMPORTANT!*PLEASE NOTE: Over the years Uberti has used multiple variations of gripframes on their SAA style revolvers, and they are not interchangeable. IF your revolver has a two-digit code inside a small rectangular box (as shown in the second picture in this listing), or if your revolver alternatively is marked with Roman numerals (i.e., “XXX” or “XXIV”), please attach a message to your order and send that code to us. If after a careful inspection you find that your revolver does not have the code (which some of the newer revolvers do not), you do not need to send the code. What these WILL NOT FIT: These WILL NOT FIT any revolvers from other makers (such as Pietta, Armi San Marco, Colt, Ruger, etc.). Also, these will NOT fit revolvers using a gripframe that is not the standard “plowhandle” shape, such as the Bisley, the Birdshead, the Thunderer, Thunderball, or the Lightning style gripframes, nor any of the Remington style revolvers such as the 1858, 1875, or 1890. Please take a careful look at the shape of your gripframe. These are for the “plowhandle” style revolvers only.04102300 A note on the Italian-produced Revolvers: The Italian firms, located in Northern Italy, have been making SAA style revolvers now for well over a half century, and have made a huge number of makes and models and grip frame profiles with varying configurations over the years. We have an in-depth knowledge of the differing grip configurations, have a large library of gripframe variations from the various makers both old and new, and have vast experience making grips for Uberti, Pietta, Armi San Marco, and the other Italian gunmaking firms. Our experienced makers go to great lengths to ensure an exacting fit, including utilizing modern precision CNC production techniques, as well as incorporating old-time hand tuning and hand checking the fit of every grip on our reference frames prior to leaving our factory. We have a long list of many satisfied customers in the shooting industry who have purchased grips to use in a wide variety of applications, and we can safely and confidently guarantee proper fit and finish to your complete satisfaction.For an additional charge, custom fitting is an option. Please contact us for further details if you are interested in custom fitting. 07132300 Arizona Custom Grips About our exclusive Magna-Tusk™ “Hi-Grade” Ivory Grips: Our Ivory grips, an exclusive of Arizona Custom Grips, are made out of a premium high-grade, ultra-high density ivory material (Magna-Tusk™), designed from the ground up as a premium grip material to greatly improve on the inherent fragility and weakness of the cheaper Bonded Ivory used on just about all factory and regular aftermarket ivory grips today. Standard Bonded Ivory is brittle, and tends to weaken and develop stress fractures over time with repeated use, firing, and handling. Magna-Tusk™ is capable of withstanding the heaviest recoil and impact, and is the toughest alternative Ivory grip material available today, while still retaining the pristine look of real ivory. These grips are not cast or made out of an inferior, lightweight material, but are heavy and dense, carefully milled out of a solid block, one at a time. Magna-Tusk is completely rock-solid, stable, and water, chemical, and oil resistant. It is flame and heat resistant, will not melt like Urethane or plastic, and is entirely void-free, with over 10x the strength, durability, and impact resistance of alternative materials. Unlike with real ivory, there is no routine care and maintenance involved, with no danger of it drying out and cracking if not maintained properly or if left in the heat. It is produced with outstanding aesthetic properties and mechanical performance. When aged with our exclusive aging process, it takes on the equivalent of a 100-year-old patina, with subtle grain details which most experts cannot tell apart from the real thing. In addition, the material has a fine grain structure, which holds intricate detail for carvings, artistic relief work, etc., found on many historic grips. Please note that the photo used is a stock photo (a sample pair). Yours will appear similar to these. Customer satisfaction is important to us – we guarantee your complete satisfaction with every purchase!!

Price: 89.95 USD

Location: Mesa, Arizona

End Time: 2023-11-30T18:16:46.000Z

Shipping Cost: 5.99 USD