Description: 【USA Stock & Fast Shipping】 【US】4 Axis CNC Kit NEMA23 76mm Stepper Motor Driver USB Mach3 Board Power Supply for CNC Router Milling Engraving Machine Good News: We have USA Warehouse in United States,so we will ship from USA Warehouse to United States. Parcel include:4× Nema23 stepper motor4× TB6600 stepper motor driver1× 4 Axis Mach3 USB CNC control board1× USB Cable1× CD disc1× 350W 24V DC Switching power supply Nema23 Stepper Motor 76mm/270Oz-in/ 3A 1.8NmGeneral Specification:Step angle accuracy: ±5%(full step,not load)Resistance accuracy: ±10%Inductance accuracy: ±20%Temperature rise: 80deg Max(rated current,2 phase on)Ambient temperature ----------—20deg ~+50degInsulation resistance:100MΩ Min,500VDCInsultion Strength--------500VAC for one minuteWiring:A+ : RedA- : GreenB+ : YellowB- : BlueTB6600 Stepper Motor Driver 4.5AParameters:The working voltage is DC 10V-45V.Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560.The rated maximum output reaches: ±4.5A. Automatic half-flow function.Suitable for 42, 57, 86 two-phase/four-phase/four-wire/six-wire stepper motors within 4.2A.Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions.Description:There are two input terminals, both of which adopt the common anode input mode.The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required.The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked.The motor rotates forward when CW is high or suspended, and reverses when it is low.When EN is high or floating, it is working state, when it is low, it is offline.Note 1: The power supply cannot be connected reversely, otherwise the chip will be burnt out.Note 2: The set current should not exceed the rated current of the motor.Mach3 USB Motion Control Board 4-axisFeatures:Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor.Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable.4 general-purpose inputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device.1 status LED, indicate connection status on the board.Have 0-10V output port, you can use mach3 software to control the spindle motor speed.Support for 4-axis linkage, you can connect four stepper motor drives or servo drives.Fuctions and Notices:Support automatic probe tool.Support Emergency input.Support for limit switch (It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.)Support for connecting electronic handwheel.The motion control card for machine control, with strong professional.Requires the operator to have the relevant expertise!If you are not familiar with the product and software features, make sure the machine's power switch on hand, you can quickly turn off the power.Attention:The inverter interface (AVI +, AVI-) is isolated from the computer and the main control circuit, and has strong anti-interference ability.No interference signal will be introduced due to the introduction of external strong electrical equipment.This interface can output 0 ~ 10V analog signals, and can also be configured as 0 ~ 5V output.It is recommended that the limit switch and emergency stop switch must be installed first.If these protection switches are not installed, in an emergency, in addition to pressing the emergency stop to return (sometimes too late to press), and turning off the motor power (sometimes too late to turn off), the most convenient way to stop is to pull the USB cable !! As long as the USB cable is pulled, the machine will automatically stop! !! !!350W 24V DC Switching Power SupplySpecification:DC output: 24V 0-14.5AInlet stability: ±0.5%Load stability: ±0.5%DC voltage of Adjustable range: ±10%AC input voltage range: 115VAC/6.5A/50HZ----230VAC/3.4A/60HZ; Selected by switchOverload protection: 105%-135% cut off the output, automatic recoveryOver-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recoverSetup/rise/hold-up time: 200ms、50ms、20ms/230VAC at full loadWithstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minuteIsolation resistance: I/P-O/P、 I/P-FG、O/P-FG: 500VDC/100MΩWorking Temperature: -10℃~+50℃ PaymentWe accept payment through PAYPAL only. Shipping 1.Items will be shipped within 1-2 days upon the receipt of payment.2.Please check out your address carefully when processing order.We are not responsible for wrong or undeliverable address.We will ship item to your PAYPAL address. If other address, please advise us by eBay or E-mail.3.The estimated delivery time is 7~15 workings days to Asian, USA, AU, UK and most western European countries;15~30 workings days to most other countries. Return&Refund 1.Any reason required for all refund.Item must be in it's original condition and no physical damage,buyer responsible for all shipping cost.2.When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos,we will help you to solve any problems. Contact 1.If you are not satisfied, please contact us to resolve any issues. Please do NOT leave negative feedback without asking for help. We work hard to make sure EVERY CUSTOMER 100% satisfaction.2.For any inquiries,issues or assistanceplease contact us via eBay or leave your mail address.3.All emails will be answered within 1-2 working days.If you do not receive our reply,please kindly re-send your email and we will reply to you as soon as possible.
Price: 144 USD
Location: Dallas
End Time: 2023-09-12T02:33:27.000Z
Shipping Cost: 20 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Model: 4 Axis nema23 stepper motor controller kit
Country/Region of Manufacture: China
Holding Torque: 270 oz-in/180N.cm
Name: 23HS8430/TB6600
Step Angle(degrees): 1.8 deg
Type: Hybrid
Current: 3A
Current Type: DC
MPN: Does Not Apply
Brand: RATTM MOTOR
Phase: 2
Driver: TB6600
Power supply: 350W,24V/15A
Motor size: 57x57x76mm